Fire dampers with fire resistance up to 120 minutes for big dimensions, approved CE marked with performance declared according to EN 15650: 2010 with fire determined resistance according to EN 1366-2 up to EI 120 (ve i ↔ o) S - (500Pa) and EI 120 (ho i ↔ o)S - (500Pa) depending on the support of installation. The dampers can be equipped with different types of mechanisms, depending on specific needs related to the project.
Micro-thermo mechanical operating : code CU2 + CFTH + FDCU
Driven by electronic servomotor RFT:
code CU2 + ONE T - 24/230 V FDCU
Driven by servomotor Belimo : code CU2 + BFLT / BFNT - 24 / 230 V
With electromagnet drive normally energized or normally de-energized code CU2 + UNIQ VD/VM FDCB
-Parete rigida: EI 120 (ve i ↔ o) S – (500 Pa).
-Parete leggera: EI 120 (ve i ↔ o) S – (500 Pa) (blocchi di gesso).
-Parete leggera: EI 120 (ve i ↔ o) S – (500 Pa) (cartongesso tipo F).
-Solaio: EI 120 (ho i ↔ o) S – (500 Pa) calcestruzzo aerato.
- Mod . CU2 / B version for battery assembly
- Mod . CU2L version with lengthened tunnel on one or both sides to hold the entire blade
- Mod . CU4 damper with EI 240 resistance (ve i ↔ o) S - ( 500 Pa ) for brick walls
- Mod . CU2 / 15 damper with EI 120 resistance (ve i ↔ o) S and pressure (1500 Pa ) for rigid walls
Struttura in materiale refrattario.
Pala in refrattario da 45 mm di spessore.
Dimensioni: da 200x200 a 1500x1000.
Guarnizione perimetrale termo-espandente.
Due microinterruttori (uno di inizio ed uno di fine corsa) già installati.
Flangia di connessione da 30 mm.
Cassa da 400 mm.
Facilità di installazione.
Installazione testata in batteria.
Tenuta d'aria classe B secondo EN1751.
Adatta per installazione a incasso ruotabile in ogni direzione 0/90/180/270°.
Adatta per parete rigida, pavimento rigido e parete leggera (cartongesso).
Non richiede manutenzione.
Per uso in ambienti interni.
Dimensioni intermedie su richiesta.
Temperatura di esercizio: max 50°C.
Il servomotore a microprocessore con ritorno a molla ONE Rf-t è progettato per azionare in modo efficiente le serrande tagliafuoco Rf-t di qualsiasi dimensione.
Le principali caratteristiche dell’attuatore ONE Rf-t sono le seguenti:
• bassissimo consumo energetico in stand-by (0,12 W) che permette un consumo di energia fino a 5 volte inferiore rispetto ai tradizionali servomotori installati nelle serrande tagliafuoco;
• lo stato di apertura della serranda tagliafuoco è visibile tramite indicatore posto sull'attuatore, inoltre un led indica se il dispositivo è alimentato;
• il dispositivo di attivazione termica principale permette di effettuare test operativi anche in assenza della rete elettrica;
• un ulteriore dispositivo di attivazione è integrato nell'attuatore al fine di rilevare un possibile incendio all'esterno del condotto;
• la sostituzione del fusibile è facile e veloce. L'alloggiamento del fusibile si trova nel corpo del servomotore e può anche esser utilizzato come foro di ispezione per una telecamera endoscopica;
• il reset manuale della serranda può essere eseguito mediante una comune batteria da 9 Volt alcanina. Con una sola batteria si possono eseguire fino a 50 cicli di reset;
• involucro IP54 in polimero tecnico resistente agli urti.
• è presente una coppia di microinterruttori di inizio e fine corsa. Sia i cavi di alimentazione e di posizione sono sovradimensionati e ben identificati.
• Alimentazione 24 VCA/VCC (-10/+20%) o 230 VCA (-15/+15%).
THE CU2 FIRE DAMPERS CAN IN FACT BE INSTALLED WITH COUPLED FLANGES AND REALLY CLOSE TO A WALL, A CEILING OR A FLOOR.
This type of fire dampers has been optimized to minimize the installation distance between two dampers and between the damper and the adjacent wall.
x: servomotor side blade coming out
y: exit of the blade on the wall side
An(mm) | 300 | 350 | 400 | 450 | 500 | 550 | 600 | 650 | 700 | 750 | 800 | 850 | 900 | 950 | 1000 |
x (mm) | 1 | 26 | 51 | 76 | 101 | 126 | 151 | 176 | 201 | 226 | |||||
y (mm) | 2 | 27 | 52 | 77 | 102 | 127 | 152 | 177 | 202 | 227 | 252 | 277 | 302 | 327 | 352 |
An < 300mm (mm) | An ≥ 300mm (mm) | |||||||
CFTH | ONE | BFL(T) | E/RMEX(T) | CFTH | ONE | BFL(T) | BFN(T) | |
P (mm) | 78 | 104 | 96 | 118 | 78 | 104 | 96 | 100 |
Q (mm) | 180 | 191 | 110 | 95 | 180 | 191 | 110 | 110 |
Z (mm) | 62 | 47 | 47 | 72,5 | 157 | 147 | 180 | 180 |
The installer has the obligation to comply with the requirements and procedures for the installation and use of the materials described in this technical documentation, so that the conditions of installation are the same as the samples were tested.
Any deviations from the instructions, affect the validity of the product certification and declaration of correct installation. The damper can be mounted with the axis horizontally or vertically built in the wall/floor or axis horizontally for remote mounting, as in the attached installation manual.
The proper installation and filling is a complex and delicate subject and it isn't sometimes accessible to installers.
Thanks to the partnership with Rf-t, Ecoclima offers a great variety of rectangular and circular european dampers, equipped with DIBt Deutsche Institut für Bautechnik marking. The installation and filling system is based on the WEICHSCHOTT method, which is fast and suitable also for great dimension openings.
The filling system is made of panels with fire resistant coating, acrylic sealant and fire resistant endothermic paint. The panels CFS-CT B protect the opening crossing from the fire. They have a minimum thickness of 100 mm. They're white painted, easy to cut and there is no mineral fiber risks. The dimension of the panel is 100x600x50 mm and the approximate density is 140 Kg/bq. The fire resistant acrylic sealant CFS-S ACR C is used in combination with the fire resistant panels for the filling of small openings, thanks also to the easy application and distribution of the product. The fire resistant paint CFS-S ACR PW is used in combination with the fire resistant panel for the filling of medium or large openings. It's easy to apply and distribute, it's effective also with a single layer of product.